Mazda 323

since 1985 release

Repair and operation of the car



Mazda 323

- Introduction
   About this Management
   Mazda-323 brand cars — the introduction
   Identification numbers of the car
   Acquisition of spare parts
   Technology of service, tools and equipment of a workplace
   Start of the engine from an auxiliary source
   Poddomkrachivaniye and towage
   Automobile chemicals, oils and lubricants
   Diagnostics of malfunctions
   Routine maintenance
   - Works on maintenance
      Oil replacement
      Replacement of an oil filter
      Replacement of a perepuskny oil filter
      Visual check on oil leak
      Check of level of engine oil
      Check of level of cooling liquid
      Replacement of cooling liquid
      Visual check of tightness of the cooling system
      Frost resistance check
      Adjustment of gaps of valves
      Pulling up of bolts of a head of cylinders
      Pulling up of bolts of inlet and final collectors
      Check of the sensor of provision of a butterfly valve
      Check of the moment of ignition
      Replacement of candles ignition/check of electric contacts
      Replacement of an element of the air filter
      Discharge of a sediment of the fuel filter of the diesel engine / replacement of the fuel filter
      Check of a maple belt / tension / replacement of a gear belt
      Visual check of system of production of the fulfilled gases
   + Box transfers/drive of wheels
   + Brakes/tires/wheels
   + Steering management / drive of forward wheels
   + Car electric equipment
   + Body / internal equipment
+ Petrol engines
+ Engine lubrication system
+ Engine cooling system
+ System of ignition
+ Power supply system, carburetor, system of injection of fuel
+ Diesel engine
+ System of production of the fulfilled gases
+ Coupling
+ Manual transmission
+ Automatic transmission
+ Suspension bracket and system of steering
+ Brake system
+ Wheels and tires, body, coloring of the car, care of the car
+ System of electric equipment
+ Heater, system of lighting, devices
+ Governing bodies and methods of operation
+ Electric circuits






Replacement of candles ignition/check of electric contacts

The special tool will be required:

  • Candle key.
  • It is in addition recommended to buy special nippers, for example, of HAZET 1849 for simplification of removal of tips of candles.

The following spare parts have to be bought:

Removal

 PERFORMANCE ORDER

  1. To disconnect all tips of candles, at the same time it is necessary to pull for plugs, but not for cables. Above-mentioned nippers facilitate removal.
  2. To blow niches of candles compressed air that by the removed candlelight dirt could not get to openings.
  3. To turn out candles a candle key and to check a condition of candles (appearance). In the presence of some experience it is possible to draw conclusions on a condition of the engine from this:

Electrodes and insulators

Average-gray — the correct work of a secha of ignition and quality of mix

Black — mix too rich

Light gray — mix too poor

Are greasy — interruptions in work of the corresponding candle or low insulation of piston rings (to check a compression).

 PERFORMANCE ORDER

  1. To check insulators of candles for superficial currents of leak. Superficial currents leave thin, uneven marks on a surface. Perhaps it is required to replace untight tips of candles.

Installation

 PERFORMANCE ORDER

  1. Before installation to check distance between electrodes by means of the flat probe.
  1. At new candles the distance between electrodes is, as a rule, established correctly, see the Head Sistem of ignition, the Section of the Candle for MAZDA 323.
  1. For adjustment of distance between contacts it is necessary to turn in a weight electrode. For this purpose there is simple, practical adaptation, otherwise to knock on a weight electrode. At a podgibaniye to rest the small screw-driver against a candle carving, at all not against the central electrode as differently it will be damaged.
  1. To clear a carving on candles a pure rag.
  2. To screw in spark plugs a hand to a prileganiye to a head of cylinders.

At the same time not to warp a candle.

  1. To tighten spark plugs with effort of 20 Nanometers.

If there is no dynamometer key, to tighten new spark plugs a candle key on 90 ° (1/4 turns). To tighten the candles which were in the use only on 15 °. Too strongly tightened candles can break or damage at a vyvinchivaniye a carving in a head of cylinders. In this case to make repair of a carving repair inserts of UTC or Heli - Coil.

  1. To connect tips of candles according to an order of ignition 1-3-4-2.
  2. To check durability of landing of tips of candles and cables of ignition.

Check of electric sockets

 PERFORMANCE ORDER

  1. To check durability of landing of all electric sockets on the ignition coil.
  2. To replace the burst plugs.
  3. To clear corroded contacts by a wire brush or a skin, if necessary to spray spray for contacts.
  4. Contacts should not be damp, otherwise clear contacts and spray spray for contacts.
  5. To bend cables of ignition and to check existence of cracks. If necessary to replace all cables of ignition.