Mazda 323

since 1985 release

Repair and operation of the car



Mazda 323

- Introduction
   About this Management
   Mazda-323 brand cars — the introduction
   Identification numbers of the car
   Acquisition of spare parts
   Technology of service, tools and equipment of a workplace
   Start of the engine from an auxiliary source
   Poddomkrachivaniye and towage
   Automobile chemicals, oils and lubricants
   Diagnostics of malfunctions
   Routine maintenance
   - Works on maintenance
      Oil replacement
      Replacement of an oil filter
      Replacement of a perepuskny oil filter
      Visual check on oil leak
      Check of level of engine oil
      Check of level of cooling liquid
      Replacement of cooling liquid
      Visual check of tightness of the cooling system
      Frost resistance check
      Adjustment of gaps of valves
      Pulling up of bolts of a head of cylinders
      Pulling up of bolts of inlet and final collectors
      Check of the sensor of provision of a butterfly valve
      Check of the moment of ignition
      Replacement of candles ignition/check of electric contacts
      Replacement of an element of the air filter
      Discharge of a sediment of the fuel filter of the diesel engine / replacement of the fuel filter
      Check of a maple belt / tension / replacement of a gear belt
      Visual check of system of production of the fulfilled gases
   + Box transfers/drive of wheels
   + Brakes/tires/wheels
   + Steering management / drive of forward wheels
   + Car electric equipment
   + Body / internal equipment
+ Petrol engines
+ Engine lubrication system
+ Engine cooling system
+ System of ignition
+ Power supply system, carburetor, system of injection of fuel
+ Diesel engine
+ System of production of the fulfilled gases
+ Coupling
+ Manual transmission
+ Automatic transmission
+ Suspension bracket and system of steering
+ Brake system
+ Wheels and tires, body, coloring of the car, care of the car
+ System of electric equipment
+ Heater, system of lighting, devices
+ Governing bodies and methods of operation
+ Electric circuits






Replacement of a perepuskny oil filter

Diesel engines to 9/89 g of the issue have perepuskny an oil filter. It is on the branch pipe screwed on the case pallet.

 PERFORMANCE ORDER

  1. To unscrew an oil filter. The oil filter is, looking in the direction of the movement, behind on the block of cylinders. For unscrewing of the filter there is a special tool, for example, of HAZET 2172. It is also possible to hammer sideways into the filter the sharp screw-driver. Oil will follow at the same time — to substitute capacity.
  1. To clear a flange of an oil filter on the block of cylinders fuel. To remove laying of the filter.
  1. To slightly cover rubber laying on the filter with engine oil.
  2. To screw the new filter a hand. When laying of the filter adjoins to the block of cylinders, to tighten the filter a coupling tape on 4/3 turns. To follow instructions on the filter.

Filling

 PERFORMANCE ORDER

  1. To fill in new oil in a jellied mouth of a cover of a head of cylinders. Then to check oil level the probe.
  2. To screw a cover of a jellied mouth.

It is recommended to fill in at first on 1/2 liters of oil less, to warm up the engine and in a few minutes to check oil level the probe, if necessary to add oil. Excess oil has to be pumped out, otherwise laying of the engine or the catalyst can be damaged.

  1. After a trial trip to check tightness of a drain stopper and an oil filter, if necessary carefully to tighten.
  2. To kill the heated-up engine and in 2 minutes to double-check oil level, if necessary to add.
  1. The difference between the top mark - F-and the lower mark - L-makes about 0,8 l. Level of oil has to be constantly between these marks.

Never to fill in oil above a mark - F-. Too large amount of oil can damage the catalyst in use.

  1. For the best control of dynamic characteristics of the engine when replacing it is necessary to use always oil of one type and whenever possible one brand. Therefore it is expedient to fix at each replacement of oil on the engine the plate on which the brand and viscosity of oil are specified.
  2. Causeless use of oils of different types is adverse. Engine oils of one type, but different brands whenever possible should not mix up. Oils of one type and brand, but with different viscosity can mix up if necessary with each other when changing a season.