Repair and operation of the car Mazda 323 - Removal and installation of a back depreciation rack//m323.ru

Mazda 323

since 1985 release

Repair and operation of the car



Mazda 323

+ Introduction
+ Petrol engines
+ Engine lubrication system
+ Engine cooling system
+ System of ignition
+ Power supply system, carburetor, system of injection of fuel
+ Diesel engine
+ System of production of the fulfilled gases
+ Coupling
+ Manual transmission
+ Automatic transmission
- Suspension bracket and system of steering
   Forward suspension bracket — the general information
   Removal and installation of a depreciation rack
   Dismantling of a depreciation rack / removal and installation of the shock-absorber / screw spring
   Check of the shock-absorber
   Removal and installation of the cross lever / replacement of a rubber support
   Check/replacement of a support of the cross lever / rotary fist
   Removal and installation of a power shaft
   Removal and installation of an intermediate shaft
   Check/dismantling of a driving shaft / replacement of cuffs
   Bearing of a forward nave
   Back suspension bracket
   Removal and installation of a back depreciation rack
   Dismantling of a back depreciation rack / removal and installation of the shock-absorber / screw spring
   Cross levers / longitudinal lever / stabilizer
   Check of the hug bearing
   Removal and installation of the hug bearing
   Adjustment of a side play of the hug bearing
   Removal and installation of a nave
   Steering
   Removal and installation of a steering wheel
   Removal and installation of a tip of steering draft
   Removal and installation of a rubber cuff of the steering drive
   Servoupravleniye pump
   Angles of installation of wheels
   Values for check of MAZDA 323
+ Brake system
+ Wheels and tires, body, coloring of the car, care of the car
+ System of electric equipment
+ Heater, system of lighting, devices
+ Governing bodies and methods of operation
+ Electric circuits






Removal and installation of a back depreciation rack

Removal

 PERFORMANCE ORDER

  1. If necessary to remove a side upholstery in salon to reach the top bolts of a depreciation rack.
  2. To weaken nuts of wheels of the car standing on the earth.
  3. To change the provision of a disk of a wheel concerning a nave that the balanced wheel could be established in former situation.
  4. To lift a back part of the car.
  5. To remove a wheel.
  1. Only the four-wheel drive: To unscrew a bolt - And - which fixed the longitudinal lever on a suspension bracket beam. Then to weaken a bolt - In - without unscrewing. If is available, in addition to unscrew an air hose of system of adjustment of height of a road gleam on the shock-absorber from above.
  1. To remove a bracket-1-and to release a brake hose from the holder on a depreciation rack.

Not to unscrew a brake hose.

  1. To prop up a suspension bracket beam a support or the hydraulic elevator that it did not fall down when weakening a depreciation rack.
  1. To unscrew 2 nuts of a-2-depreciation rack on a suspension bracket beam, to remove bolts-3-.
  1. To unscrew 2 nuts on the top support of a depreciation rack and to take out a depreciation rack-5-.
  2. If necessary to sort a depreciation rack, see the Head Razbork of a back depreciation rack / removal and installation of the shock-absorber / a screw spring.

Installation

 PERFORMANCE ORDER

  1. To insert a depreciation rack, to tighten 2 top nuts with effort of 30 Nanometers.
  2. To insert 2 bolts of a depreciation rack on a beam in front back, to tighten nuts with effort of 110 Nanometers.
  3. To remove the elevator from under a beam.
  4. To strengthen a brake hose on a depreciation rack.
  5. Only the four-wheel drive: To tighten bolts - And - and - In - with effort of 70 Nanometers. In the presence of system of adjustment of height of a road gleam to screw an air hose from above on the shock-absorber with effort of 20 Nanometers.
  6. To screw a wheel, at the same time considering a tag on a nave. To lower the car and to tighten nuts of wheels cross-wise with effort of 100 Nanometers.
  7. If it is removed, to establish an internal upholstery over a depreciation rack.
  8. To perform measurements of angles of installation of wheels.