Mazda 323

since 1985 release

Repair and operation of the car



Mazda 323

+ Introduction
+ Petrol engines
+ Engine lubrication system
+ Engine cooling system
+ System of ignition
+ Power supply system, carburetor, system of injection of fuel
+ Diesel engine
+ System of production of the fulfilled gases
+ Coupling
+ Manual transmission
+ Automatic transmission
- Suspension bracket and system of steering
   Forward suspension bracket — the general information
   Removal and installation of a depreciation rack
   Dismantling of a depreciation rack / removal and installation of the shock-absorber / screw spring
   Check of the shock-absorber
   Removal and installation of the cross lever / replacement of a rubber support
   Check/replacement of a support of the cross lever / rotary fist
   Removal and installation of a power shaft
   Removal and installation of an intermediate shaft
   Check/dismantling of a driving shaft / replacement of cuffs
   Bearing of a forward nave
   Back suspension bracket
   Removal and installation of a back depreciation rack
   Dismantling of a back depreciation rack / removal and installation of the shock-absorber / screw spring
   Cross levers / longitudinal lever / stabilizer
   Check of the hug bearing
   Removal and installation of the hug bearing
   Adjustment of a side play of the hug bearing
   Removal and installation of a nave
   Steering
   Removal and installation of a steering wheel
   Removal and installation of a tip of steering draft
   Removal and installation of a rubber cuff of the steering drive
   Servoupravleniye pump
   Angles of installation of wheels
   Values for check of MAZDA 323
+ Brake system
+ Wheels and tires, body, coloring of the car, care of the car
+ System of electric equipment
+ Heater, system of lighting, devices
+ Governing bodies and methods of operation
+ Electric circuits











Removal and installation of the hug bearing

Cars to 9/89 g of the issue and the station wagon model (not all-wheel drive)

Holders of the two-component hug bearing on cars to 9/89 g of the issue are in the brake drum, on cars with back disk brakes — in a brake disk. After each installation the side play of the bearing has to be regulated by a nut.

Removal

 PERFORMANCE ORDER

  1. To remove the brake drum or a brake disk, see the Head the Brake system.

The nave nut on the left side of the car has the left carving, for easing it should be rotated to the right (clockwise).

  1. To remove the released parts of the bearing.
  2. To wipe and examine bearing holders. With defects or visible wear all bearing has to be replaced. Not to disassemble the bearing needlessly if it is not required.
  3. To take out an epiploon.
  1. To beat out both external holders a brass core. At the same time to rearrange a core on a circle on various places in order to avoid a distortion of holders.

Not to apply a steel core that on holders were not formed agnails.

  1. In case of wear to remove an internal holder of the bearing from a pin a standard stripper.

Installation

 PERFORMANCE ORDER

  1. Always to replace the hug bearing in a set (an internal and external holder and also a body of swing) even if only one holder is damaged.
  2. To visually check a pin for existence of damages and wear, if necessary to replace.
  1. To evenly hammer bearing holders - With - by means of the hammer and a brass core against the stop. It is better to use a stationary press if that is available, with a mandrel of the corresponding diameter.
  1. To fill the conic roller bearing with lubricant (lithium).
  2. To insert the internal bearing.
  1. To evenly press a new epiploon by means of an equal plate, not to strike blows with the hammer directly to an epiploon.
  1. To cover an epiploon with lubricant.
  2. To install the brake drum, or a brake disk and at the same time also to insert the external conic roller bearing, see the Head the Brake system.
  3. To adjust a hug bearing side play.
  4. To screw a wheel, considering a tag on a nave. To lower the car and to tighten wheel nuts cross-wise with effort of 100 Nanometers.