Mazda 323

since 1985 release

Repair and operation of the car



Mazda 323

+ Introduction
+ Petrol engines
+ Engine lubrication system
+ Engine cooling system
+ System of ignition
- Power supply system, carburetor, system of injection of fuel
   Rules of purity during the work with a power supply system
   Removal and installation/check of the sensor in the fuel tank
   Removal and installation of the fuel tank
   Removal and installation of the fuel pump
   Removal and installation/check of the fuel pump
   Removal and installation of the air filter
   - Carburetor
      Adjustment of the carburetor
      Malfunctions in a fuel supply system
      The carburetor with the falling stream and consecutive turning on of cameras
      Check and adjustment of contents WITH
      Check/removal and installation of the valve of interruption in supply of fuel
      Check/removal and installation of automatic equipment of cold start
      Removal and installation of the carburetor
   + System of injection of fuel
+ Diesel engine
+ System of production of the fulfilled gases
+ Coupling
+ Manual transmission
+ Automatic transmission
+ Suspension bracket and system of steering
+ Brake system
+ Wheels and tires, body, coloring of the car, care of the car
+ System of electric equipment
+ Heater, system of lighting, devices
+ Governing bodies and methods of operation
+ Electric circuits






Removal and installation of the carburetor

At removal of the carburetor a fuel quantity can act. Vapors of fuel are poisonous and flammable therefore to pay special attention to good ventilation of a workplace. To avoid hit of fuel on skin, to work in toplivostoyky mittens. Not to work near naked flame.

Removal

 PERFORMANCE ORDER

  1. To disconnect a weight cable from the battery.

At the same time data from memory of malfunctions of the engine or a protective code of the radio receiver are erased. Before shutdown of the battery it is necessary to read instructions in the Section Removal also installation of the battery.

  1. To remove the air filter-2-, see the Head the Power supply system, the carburetor, system of injection of fuel, the Section Removal and installation of the air filter.
  2. If is available, to unscrew the holder from the air filter.
  3. To remove the gas-3-drive. Previously to mark the adjusting provision of a cover of a cable on a countersupport.

The cable of gas should not be bent, otherwise it will burst in use. Anyway to replace the bent cable.

  1. To disconnect a fuel-supply line-4-and to stop up it, previously having weakened and having shifted a collar back. As a cap the pure bolt of the corresponding diameter can be used.
  2. To disconnect vacuum hoses-5-on the case of the carburetor and to mark them with an adhesive tape.
  1. To disconnect electric connections-6-and-7-and to mark them with an adhesive tape.
  1. To unscrew a nut of fastening of the carburetor and to raise the carburetor-8-.
  2. To remove the heating plug.
  3. To remove a heater-9-and laying.
  4. To cover an inlet pipe with a pure rag that there dirt could not get.

Installation

 PERFORMANCE ORDER

  1. To remove a rag, to install the carburetor with new laying on a flange and to screw it.
  2. To connect vacuum hoses according to marking to the carburetor case.
  3. To connect a fuel hose and to fix by a collar.
  4. To install the drive of gas and the starting gate. To clamp a cable cover according to the put marking.
  5. To attach a returnable spring of the lever of a butterfly valve.
  6. If is available, to screw the holder of the air filter.
  7. To install the air filter, see the Head the Power supply system, the carburetor, system of injection of fuel, the Section Removal and installation of the air filter.
  8. To connect a cable of mass of the battery.
  9. If are available, to determine time on hours and to set a protective code of the radio receiver.
  10. To check idling and maintenance WITH, if necessary to adjust.